095000-7500 Diesel Fuel Injector for Mitsubishi 4M41 3.2L

095000-7500 Denso diesel fuel injector for Mitsubishi 4M41 3.2L DI-D

The 095000-7500 Denso diesel fuel injector is supplied by Rayfuel as an aftermarket replacement for selected Mitsubishi applications using the 4M41 3.2L DI-D diesel engine, including versions listed around 2009 with a 147 kW output reference. It cross-references Mitsubishi OE number 1465A279 and is intended for part-number-matched fuel-system repair. Repair workshops, wholesalers and distributors can find related products in our Denso common rail injector range.

095000-7500 Denso diesel fuel injector identification

• Primary part number: 095000-7500
• OE reference: 1465A279
• Vehicle reference: Selected Mitsubishi diesel applications
• Engine reference: 4M41 3.2L DI-D
• Output and year reference: 147 kW, around 2009
• Product type: Common rail diesel fuel injector
• Product brand: Rayfuel

Compare both 095000-7500 and 1465A279 with the identification on the injector removed from the engine. The Denso wording in the SEO fields describes the fuel-injection system and the part-number family used by buyers; it does not claim that this Rayfuel aftermarket replacement is a genuine Denso or Mitsubishi boxed component. The product photographs show the injector body, electrical connector, high-pressure inlet, return connection and nozzle profile for visual comparison.

Mitsubishi 4M41 application and fitment

Mitsubishi identifies the 4M41 as a 3.2-liter direct-injection diesel engine used in selected Pajero-family applications. However, the 4M41 engine was produced in different vehicle markets, model years and calibration versions. Injector selection can therefore depend on the exact vehicle code, production date, emissions specification and engine-control configuration. A general 4M41 or 3.2 DI-D description alone does not guarantee compatibility.

Before ordering, verify the number stamped on the old injector and confirm the vehicle model, VIN or chassis code, production year, engine designation and rated output. Compare the connector shape, fuel connections, mounting profile and nozzle end with the supplied images. If the original unit has a different number, obtain a verified supersession or cross-reference rather than selecting only by engine capacity.

Common rail injector function

A common rail injector meters pressurized diesel fuel and delivers it into the combustion chamber in response to the engine control system. Correct injection quantity, timing and spray behavior support reliable starting, balanced combustion, stable idle and normal response under load. Wear, internal leakage, contamination or an electrical fault can interfere with these functions, but the 095000-7500 Denso diesel fuel injector should be replaced only after suitable diagnosis.

Common signs an injector may need checking

• Hard starting or extended cranking
• Rough idle or uneven cylinder contribution
• Reduced power during acceleration or under load
• Excessive black, white or gray exhaust smoke
• Abnormal diesel combustion noise
• Fuel leakage around the injector or sealing area
• Injector-related diagnostic trouble codes

These symptoms do not prove injector failure. Similar conditions may be caused by low rail pressure, wiring faults, contaminated fuel, poor compression, intake restrictions or other engine problems. Scan-tool data, return-flow measurement, electrical inspection and professional bench testing may be necessary before replacement.

Installation and calibration

Installation should be performed by a qualified diesel technician using clean working practices. Protect all high-pressure connections from contamination, inspect the injector pipe and replace required sealing washers or related service parts. Follow the tightening procedure specified for the exact Mitsubishi engine and vehicle. Some 4M41 versions may require injector compensation or calibration information to be registered with suitable diagnostic equipment, while procedures can vary. Do not assume that coding is always required or that every 4M41 version uses the same process.

Before you order

Please confirm OE number, engine model or old part photos before ordering. Verify 095000-7500 and 1465A279 against the removed injector, then confirm the Mitsubishi model, 4M41 engine version, year and market. Mitsubishi’s official company and engine history identifies the 4M41 as a 3.2L direct-injection diesel engine, but final injector fitment must still be confirmed by the exact part number. Send clear photos and vehicle information through the Rayfuel contact page when you need compatibility support.

The 095000-7500 Denso diesel fuel injector is intended for OE-number-matched aftermarket replacement in compatible Mitsubishi 4M41 3.2L DI-D applications. Final fitment depends on the exact vehicle and old-part identification.

Rayfuel supply and support

Rayfuel supplies diesel injection parts to repair shops, wholesalers and distributors worldwide. Support includes number comparison, photo-based fitment checks, quantity quotations, mixed-parts inquiries and secure export packaging. Contact us before shipment when you need several injectors or confirmation for a specific Mitsubishi vehicle market.