095000-5226 Diesel Fuel Injector for Hino 700 E13C

095000-5226 Denso diesel fuel injector for Hino 700 E13C

The 095000-5226 Denso diesel fuel injector is supplied by Rayfuel as a new aftermarket replacement for selected Hino 700 heavy-duty trucks using the E13C diesel engine. It cross-references Hino number 23670-E0341 and is intended for workshops, fleet operators and parts buyers who have confirmed the number on the removed injector. Browse related products in our Denso common rail injector range.

This item is a Rayfuel aftermarket product for a Denso common-rail system. It is not described as a genuine Hino or genuine Denso boxed component. Similar injector versions in the 095000-522 series may share an external design while differing in calibration or application, so the complete suffix and OE number must be checked.

Product Identification

• Primary part number: 095000-5226
• Hino cross-reference: 23670-E0341
• Product type: Common rail diesel fuel injector assembly
• Injection system: Denso system
• Vehicle application: Selected Hino 700 trucks
• Engine application: E13C diesel engine
• Product brand: Rayfuel

The primary number 095000-5226 identifies the injector supplied in this listing. The punctuation-free form 0950005226 is only a writing variation. Hino number 23670-E0341 is the supplied OE reference. Other close numbers should not be treated as automatic replacements without confirmation for the exact truck and engine specification.

095000-5226 Denso diesel fuel injector application and fitment

This injector is listed for selected Hino 700 Series vehicles equipped with the E13C engine. Fitment may vary according to truck market, production date, engine serial number, emissions configuration and parts supersession. The Hino 700 or E13C description is useful for initial identification but does not replace an exact part-number check.

Compare 095000-5226 and 23670-E0341 with the markings on the removed injector or a reliable VIN and engine-serial parts record. Also inspect the electrical lead and connector, high-pressure inlet, return connection, hold-down body, nozzle-end profile and overall arrangement shown in the gallery. Contact Rayfuel with old-part photos if the markings are incomplete.

Injector Function and Performance

A common-rail injector meters high-pressure diesel fuel and delivers controlled injection events to the combustion chamber. Correct operation contributes to dependable starting, stable idle, balanced cylinder output and consistent response under load. Results also depend on rail pressure, fuel cleanliness, wiring, compression and the condition of the complete fuel system.

Common Signs This Injector May Need Replacing

• Hard starting or extended cranking
• Rough idle or uneven cylinder contribution
• Loss of power under load
• Increased exhaust smoke
• Abnormal diesel combustion noise
• Excessive return-flow measurement
• Injector-related diagnostic fault codes

These symptoms do not prove injector failure. Low rail pressure, restricted fuel supply, wiring problems, contaminated diesel or mechanical engine faults can cause similar complaints. Professional diagnosis and injector testing are recommended before ordering replacement parts.

Installation and Coding

Installation should be completed by a qualified diesel technician under clean workshop conditions. Keep all high-pressure openings protected from contamination, inspect associated pipes and use the seals and tightening procedure specified for the engine. Depending on the E13C control-system version, injector compensation data may need to be checked or registered using suitable diagnostic equipment. Coding requirements should be confirmed from the correct service information.

Before You Order

Please confirm OE number, engine model or old part photos before ordering. Verify the full 095000-5226 and 23670-E0341 numbers, then confirm the truck VIN and engine serial specification. Hino provides general manufacturer information at its global website; exact injector selection must still follow the appropriate parts record. Use the Rayfuel contact page for photo-based fitment assistance.

The 095000-5226 Denso diesel fuel injector is an OE-number-matched aftermarket replacement for confirmed Hino 700 E13C applications.

Rayfuel Supply and Support

Rayfuel supplies diesel injection components to repair shops, wholesalers, distributors and fleet service businesses. Support includes part-number comparison, old-part photo checks, quantity quotations, mixed-parts inquiries and export packaging. Contact us if you require multiple E13C injectors or need help checking a specific Hino 700 application.